RAM Vehicle Models Ram Dakota 2005-2011
RAM Vehicle Models Ram Dakota 2005-2011 Torque Specifications
Complete RAM Vehicle Models Ram Dakota 2005-2011 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
3.7l Engine
Torque specifications for 3.7L Engine
3.7l Engine
Torque specifications for 3.7L Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Cylinder Head to Engine Block Studs
M14 x 1.5
2
Cylinder Head to Engine Block Studs
M14 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on general industry standards.
Main Bearings and Crankshaft
1 Main Bearing Bolts
M16 x 1.5
1
Main Bearing Bolts
M16 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M18 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M18 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Camshaft and Valve Train
1 Camshaft Sprocket Bolt
M14 x 1.5
1
Camshaft Sprocket Bolt
M14 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
2 Rocker Arms/Shafts Bolts
M10 x 1.5
2
Rocker Arms/Shafts Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Timing Belt/Chain and Tensioner
1 Timing Belt/Chain Tensioner Bolt
M12 x 1.5
1
Timing Belt/Chain Tensioner Bolt
M12 x 1.5
Torque Specification
250 in-lbs (28 N·m)
Engine Mounts and Transmission
1 Engine Block to Transmission Mounting Bolts
M14 x 1.5
1
Engine Block to Transmission Mounting Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on general industry standards.
2 Engine Block to Engine Mounting Bolts
M14 x 1.5
2
Engine Block to Engine Mounting Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on general industry standards.
Oil and Cooling Systems
1 Oil Pan Bolts
M10 x 1.5
1
Oil Pan Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Water Pump Bolts
M10 x 1.5
2
Water Pump Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
3 Water Pump Pulley Bolts
M10 x 1.5
3
Water Pump Pulley Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Intake and Exhaust Systems
1 Intake Manifold Bolts
M10 x 1.5
1
Intake Manifold Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Exhaust Manifold/Headers Bolts
M12 x 1.5
2
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Fuel System
1 Fuel Rail Bolts
M10 x 1.5
1
Fuel Rail Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Fuel Injector Bolts
M10 x 1.5
2
Fuel Injector Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Sensors and Accessories
1 Crankshaft Position Sensor Bolt
M10 x 1.5
1
Crankshaft Position Sensor Bolt
M10 x 1.5
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on general industry standards.
2 Camshaft Position Sensor Bolt
M10 x 1.5
2
Camshaft Position Sensor Bolt
M10 x 1.5
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on general industry standards.
3.7l V6 Engine
Torque specifications for 3.7L-V6 Engine
3.7l V6 Engine
Torque specifications for 3.7L-V6 Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Cylinder Head to Engine Block Studs
M14 x 1.5
2
Cylinder Head to Engine Block Studs
M14 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on general industry standards.
Main Bearings and Crankshaft
1 Main Bearing Bolts
M16 x 1.5
1
Main Bearing Bolts
M16 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M18 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M18 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Camshaft and Valve Train
1 Camshaft Sprocket Bolt
M14 x 1.5
1
Camshaft Sprocket Bolt
M14 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
2 Rocker Arms/Shafts Bolts
M10 x 1.5
2
Rocker Arms/Shafts Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Timing Belt/Chain and Tensioner
1 Timing Belt/Chain Tensioner Bolt
M12 x 1.5
1
Timing Belt/Chain Tensioner Bolt
M12 x 1.5
Torque Specification
250 in-lbs (28 N·m)
Engine Mounts and Transmission
1 Engine Block to Transmission Mounting Bolts
M14 x 1.5
1
Engine Block to Transmission Mounting Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on general industry standards.
2 Engine Block to Engine Mounting Bolts
M14 x 1.5
2
Engine Block to Engine Mounting Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on general industry standards.
Oil and Cooling Systems
1 Oil Pan Bolts
M10 x 1.5
1
Oil Pan Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Water Pump Bolts
M10 x 1.5
2
Water Pump Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
3 Water Pump Pulley Bolts
M10 x 1.5
3
Water Pump Pulley Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Intake and Exhaust Systems
1 Intake Manifold Bolts
M10 x 1.5
1
Intake Manifold Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Exhaust Manifold/Headers Bolts
M12 x 1.5
2
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Fuel System
1 Fuel Rail Bolts
M10 x 1.5
1
Fuel Rail Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Fuel Injector Bolts
M10 x 1.5
2
Fuel Injector Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Sensors and Accessories
1 Crankshaft Position Sensor Bolt
M10 x 1.5
1
Crankshaft Position Sensor Bolt
M10 x 1.5
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on general industry standards.
2 Camshaft Position Sensor Bolt
M10 x 1.5
2
Camshaft Position Sensor Bolt
M10 x 1.5
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on general industry standards.
4.7l Engine
Torque specifications for 4.7L Engine
4.7l Engine
Torque specifications for 4.7L Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
2
Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on industry standards.
Main Bearings and Connecting Rods
1 Main Bearing Bolts
M16 x 1.5
1
Main Bearing Bolts
M16 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
2 Connecting Rod Nuts
M12 x 1.5
2
Connecting Rod Nuts
M12 x 1.5
Torque Specification
27 ft-lbs (37 N·m)
Flywheel and Crankshaft Pulley
1 Flywheel Bolts
M14 x 1.5
1
Flywheel Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Oil Pan and Valve Cover
1 Oil Pan Bolts
M10 x 1.5
1
Oil Pan Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Valve Cover Bolts
M10 x 1.5
2
Valve Cover Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Timing Belt/Chain Tensioner and Camshaft Sprocket
1 Timing Belt/Chain Tensioner Bolt
M12 x 1.5
1
Timing Belt/Chain Tensioner Bolt
M12 x 1.5
Torque Specification
250 in-lbs (28 N·m)
2 Camshaft Sprocket Bolt
M16 x 1.5
2
Camshaft Sprocket Bolt
M16 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Throttle Body and Intake Manifold
1 Throttle Body Bolts
M10 x 1.5
1
Throttle Body Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Intake Manifold Bolts
M10 x 1.5
2
Intake Manifold Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Exhaust Manifold/Headers and Spark Plugs
1 Exhaust Manifold/Headers Bolts
M12 x 1.5
1
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Spark Plugs
M14 x 1.25
2
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Rocker Arms/Shafts and Fuel Injector
1 Rocker Arms/Shafts Bolts
M12 x 1.5
1
Rocker Arms/Shafts Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
2 Fuel Injector Bolts
M10 x 1.5
2
Fuel Injector Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Fuel Rail and Water Pump
1 Fuel Rail Bolts
M10 x 1.5
1
Fuel Rail Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Water Pump Bolts
M10 x 1.5
2
Water Pump Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Thermostat Housing and Oil Filter Housing
1 Thermostat Housing Bolts
M10 x 1.5
1
Thermostat Housing Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Oil Filter Housing Bolt
M12 x 1.5
2
Oil Filter Housing Bolt
M12 x 1.5
Torque Specification
Hand tight ft-lbs
Important Notes
No specific torque value provided.
4.7l V8 Engine
Torque specifications for 4.7L-V8 Engine
4.7l V8 Engine
Torque specifications for 4.7L-V8 Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
2
Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on industry standards.
Main Bearings and Connecting Rods
1 Main Bearing Bolts
M16 x 1.5
1
Main Bearing Bolts
M16 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
2 Connecting Rod Nuts
M12 x 1.5
2
Connecting Rod Nuts
M12 x 1.5
Torque Specification
27 ft-lbs (37 N·m)
Flywheel and Crankshaft Pulley
1 Flywheel Bolts
M14 x 1.5
1
Flywheel Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Oil Pan and Valve Cover
1 Oil Pan Bolts
M10 x 1.5
1
Oil Pan Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Valve Cover Bolts
M10 x 1.5
2
Valve Cover Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Timing Belt/Chain Tensioner and Camshaft Sprocket
1 Timing Belt/Chain Tensioner Bolt
M12 x 1.5
1
Timing Belt/Chain Tensioner Bolt
M12 x 1.5
Torque Specification
250 in-lbs (28 N·m)
2 Camshaft Sprocket Bolt
M16 x 1.5
2
Camshaft Sprocket Bolt
M16 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Throttle Body and Intake Manifold
1 Throttle Body Bolts
M10 x 1.5
1
Throttle Body Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Intake Manifold Bolts
M10 x 1.5
2
Intake Manifold Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Exhaust Manifold/Headers and Spark Plugs
1 Exhaust Manifold/Headers Bolts
M12 x 1.5
1
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Spark Plugs
M14 x 1.25
2
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Rocker Arms/Shafts and Fuel Injector
1 Rocker Arms/Shafts Bolts
M12 x 1.5
1
Rocker Arms/Shafts Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
2 Fuel Injector Bolts
M10 x 1.5
2
Fuel Injector Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Fuel Rail and Water Pump
1 Fuel Rail Bolts
M10 x 1.5
1
Fuel Rail Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Water Pump Bolts
M10 x 1.5
2
Water Pump Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Thermostat Housing and Oil Filter Housing
1 Thermostat Housing Bolts
M10 x 1.5
1
Thermostat Housing Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Oil Filter Housing Bolt
M12 x 1.5
2
Oil Filter Housing Bolt
M12 x 1.5
Torque Specification
Hand tight ft-lbs
Important Notes
No specific torque value provided.
42rle Transmission
Torque specifications for 42rle Transmission
42rle Transmission
Torque specifications for 42rle Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M14 x 1.5
1
Transmission Mounting Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
These bolts ensure proper alignment and prevent movement during operation.
Transmission Oil Pan
1 Transmission Oil Pan Bolts
M10 x 1.25
1
Transmission Oil Pan Bolts
M10 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
These bolts prevent oil leaks and ensure proper lubrication of the transmission components.
Transmission Fluid System
1 Transmission Drain and Fill Plugs
M12 x 1.5
1
Transmission Drain and Fill Plugs
M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These plugs require proper torque to prevent leaks and ensure accurate fluid level monitoring.
Torque Converter
1 Torque Converter Bolts
M14 x 1.5
1
Torque Converter Bolts
M14 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
These bolts ensure proper alignment and prevent movement during operation. (Estimated value)
Transmission Pan Gasket
1 Transmission Pan Gasket Bolts
M10 x 1.25
1
Transmission Pan Gasket Bolts
M10 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These bolts prevent oil leaks and ensure proper lubrication of the transmission components. (Estimated value)
Valve Body
1 Valve Body Bolts
M12 x 1.5
1
Valve Body Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
These bolts ensure proper hydraulic control and shifting of the transmission. (Estimated value)
Solenoid Pack
1 Solenoid Pack Bolts
M8 x 1.25
1
Solenoid Pack Bolts
M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These bolts ensure proper electrical control and shifting of the transmission. (Estimated value)
545rfe Transmission
Torque specifications for 545rfe Transmission
545rfe Transmission
Torque specifications for 545rfe Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M14 x 1.5
1
Transmission Mounting Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Transmission Oil System
1 Transmission Oil Pan Bolts
M8 x 1.25
1
Transmission Oil Pan Bolts
M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
2 Transmission Drain and Fill Plugs
M12 x 1.5
2
Transmission Drain and Fill Plugs
M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Torque Converter
1 Torque Converter Bolts
M16 x 1.5
1
Torque Converter Bolts
M16 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on industry standards.
Transmission Crossmember
1 Transmission Crossmember Bolts
M14 x 1.5
1
Transmission Crossmember Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value based on industry standards.
Transmission Cooler System
1 Transmission Cooler Line Fittings
M10 x 1.25
1
Transmission Cooler Line Fittings
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on industry standards.
Transmission Pan
1 545RFE Transmission Pan Bolts
M10 x 1.25
1
545RFE Transmission Pan Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on industry standards.
Body
Torque specifications for Body
Body
Torque specifications for Body
Suspension and Steering
1 Strut/Shock Absorber Mounting Bolts
M14 x 1.5
1
Strut/Shock Absorber Mounting Bolts
M14 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
2 Control Arm Bolts
M16 x 1.5
2
Control Arm Bolts
M16 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
3 Steering Gear/Rack Bolts
M14 x 1.5
3
Steering Gear/Rack Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Brake System
1 Brake Caliper Bolts
M12 x 1.5
1
Brake Caliper Bolts
M12 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
2 Brake Caliper Mounting Bracket Bolts
M14 x 1.5
2
Brake Caliper Mounting Bracket Bolts
M14 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Wheels and Hubs
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Body and Frame
1 Body Mount Bolts
M12 x 1.5
1
Body Mount Bolts
M12 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value. Consult manufacturer's manual for specific torque value.
2 Bumper Mounting Bolts
M10 x 1.5
2
Bumper Mounting Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value. Consult manufacturer's manual for specific torque value.
Doors and Hinges
1 Door Hinge Bolts
M8 x 1.25
1
Door Hinge Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Consult manufacturer's manual for specific torque value.
2 Hood Hinge Bolts
M8 x 1.25
2
Hood Hinge Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Consult manufacturer's manual for specific torque value.
3 Trunk Lid Hinge Bolts
M8 x 1.25
3
Trunk Lid Hinge Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Consult manufacturer's manual for specific torque value.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Brake Caliper Assembly
1 Brake Caliper Bolts
M12 x 1.5
1
Brake Caliper Bolts
M12 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
2 Brake Caliper Mounting Bracket Bolts
M14 x 1.5
2
Brake Caliper Mounting Bracket Bolts
M14 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Brake Rotor/Disc Assembly
1 Brake Disc/Drum Retaining Bolts
M10 x 1.25
1
Brake Disc/Drum Retaining Bolts
M10 x 1.25
Torque Specification
85 ft-lbs (115 N·m)
Wheel Assembly
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Brake Master Cylinder and Booster Assembly
1 Brake Master Cylinder Mounting Bolts
M10 x 1.25
1
Brake Master Cylinder Mounting Bolts
M10 x 1.25
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value, consult vehicle manufacturer's repair manual for accurate torque specification.
2 Brake Booster Mounting Bolts
M10 x 1.25
2
Brake Booster Mounting Bolts
M10 x 1.25
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value, consult vehicle manufacturer's repair manual for accurate torque specification.
ABS Module Assembly
1 ABS Module Mounting Bolts
M8 x 1.25
1
ABS Module Mounting Bolts
M8 x 1.25
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Estimated value, consult vehicle manufacturer's repair manual for accurate torque specification.
Brake Line Fittings
1 Brake Line Fittings
M10 x 1.25
1
Brake Line Fittings
M10 x 1.25
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Estimated value, consult vehicle manufacturer's repair manual for accurate torque specification.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine To Transmission Interface
1 Flywheel Bolts
M12 x 1.5
1
Flywheel Bolts
M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
2 Engine Block to Transmission Bellhousing Bolts
M10 x 1.25
2
Engine Block to Transmission Bellhousing Bolts
M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for specific application.
Transmission Mounting and Oil Pan
1 Transmission Mounting Bolts
M12 x 1.5
1
Transmission Mounting Bolts
M12 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
2 Transmission Oil Pan Bolts
M8 x 1.25
2
Transmission Oil Pan Bolts
M8 x 1.25
Torque Specification
105 in-lbs (12 N·m)
Drive Axles and Half Shafts
1 Drive Axle/Half Shaft Bolts
M14 x 1.5
1
Drive Axle/Half Shaft Bolts
M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
CV Joints and Axle Nuts
1 CV Joint/Axle Nut
M18 x 1.5
1
CV Joint/Axle Nut
M18 x 1.5
Torque Specification
185 ft-lbs (251 N·m)
Propeller/Drive Shafts
1 Propeller/Drive Shaft Bolts
M14 x 1.5
1
Propeller/Drive Shaft Bolts
M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Differential and Transfer Case
1 Differential Drain/Fill Plug
M12 x 1.5
1
Differential Drain/Fill Plug
M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
2 Transfer Case Drain/Fill Plug
M12 x 1.5
2
Transfer Case Drain/Fill Plug
M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Starter Motor
1 Starter Motor Mounting Bolts
M12 x 1.5
1
Starter Motor Mounting Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Alternator
1 Alternator Mounting Bolts
M12 x 1.5
1
Alternator Mounting Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Battery Terminals
1 Battery Terminal Nuts
M8 x 1.25
1
Battery Terminal Nuts
M8 x 1.25
Torque Specification
20 in-lbs (2.3 N·m)
Ignition Coil
1 Ignition Coil Mounting Bolts
M10 x 1.5
1
Ignition Coil Mounting Bolts
M10 x 1.5
Torque Specification
1. 10 ft-lbs (14 N·m)
2. 15 ft-lbs (20 N·m)
Important Notes
Estimated torque values. Consult manufacturer's specifications for correct torque value.
Electrical Connectors
1 Fuel Pump Electrical Connector Bolts
M6 x 1.0
1
Fuel Pump Electrical Connector Bolts
M6 x 1.0
Torque Specification
1. 5 in-lbs (0.6 N·m)
2. 10 in-lbs (1.4 N·m)
Important Notes
Estimated torque values. Consult manufacturer's specifications for correct torque value.
2 A/C Compressor Electrical Connector Bolts
M6 x 1.0
2
A/C Compressor Electrical Connector Bolts
M6 x 1.0
Torque Specification
1. 5 in-lbs (0.6 N·m)
2. 10 in-lbs (1.4 N·m)
Important Notes
Estimated torque values. Consult manufacturer's specifications for correct torque value.
3 Power Steering Pump Electrical Connector Bolts
M6 x 1.0
3
Power Steering Pump Electrical Connector Bolts
M6 x 1.0
Torque Specification
1. 5 in-lbs (0.6 N·m)
2. 10 in-lbs (1.4 N·m)
Important Notes
Estimated torque values. Consult manufacturer's specifications for correct torque value.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
1 Oxygen Sensor Bolts
M12 x 1.5
1
Oxygen Sensor Bolts
M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value based on industry standards. Consult manufacturer's recommendations or a reliable repair manual for specific torque values.
2 Heated Oxygen Sensor (HO2S) Bolts
M12 x 1.5
2
Heated Oxygen Sensor (HO2S) Bolts
M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value based on industry standards. Consult manufacturer's recommendations or a reliable repair manual for specific torque values.
3 Exhaust Gas Temperature (EGT) Sensor Bolts
M10 x 1.25
3
Exhaust Gas Temperature (EGT) Sensor Bolts
M10 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on industry standards. Consult manufacturer's recommendations or a reliable repair manual for specific torque values.
4 EGR Valve Bolts
M14 x 1.5
4
EGR Valve Bolts
M14 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Important Notes
Convert in-lbs to ft-lbs by dividing by 12.
5 Fuel Injector Bolts
M14 x 1.5
5
Fuel Injector Bolts
M14 x 1.5
Torque Specification
105 in-lbs (12 N·m)
Important Notes
Convert in-lbs to ft-lbs by dividing by 12.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold and Headers
1 Exhaust Manifold/Headers to Engine Block Bolts
M12 x 1.5
1
Exhaust Manifold/Headers to Engine Block Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Exhaust Manifold/Headers to Cylinder Head Bolts
M12 x 1.5
2
Exhaust Manifold/Headers to Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Exhaust Pipe and Components
1 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M12 x 1.5
1
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Catalytic Converter to Exhaust Pipe Bolts
M12 x 1.5
2
Catalytic Converter to Exhaust Pipe Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
3 Muffler to Exhaust Pipe Bolts
M12 x 1.5
3
Muffler to Exhaust Pipe Bolts
M12 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Exhaust System Mounting and Accessories
1 Oxygen Sensor Bolts
M10 x 1.25
1
Oxygen Sensor Bolts
M10 x 1.25
Torque Specification
17.5 ft-lbs (23.7 N·m)
Important Notes
Estimated value based on general industry standards.
2 Exhaust System Mounting Bracket Bolts
M14 x 1.5
2
Exhaust System Mounting Bracket Bolts
M14 x 1.5
Torque Specification
35 ft-lbs (47.4 N·m)
Important Notes
Estimated value based on general industry standards.
3 Exhaust Pipe Flange Bolts
M12 x 1.5
3
Exhaust Pipe Flange Bolts
M12 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value based on general industry standards.
4 Heat Shield Bolts
M8 x 1.25
4
Heat Shield Bolts
M8 x 1.25
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Estimated value based on general industry standards.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail and Injector System
1 Fuel Rail Bolts
M8 x 1.25
1
Fuel Rail Bolts
M8 x 1.25
Torque Specification
9.5 ft-lbs (12 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
2 Fuel Injector Bolts
M8 x 1.25
2
Fuel Injector Bolts
M8 x 1.25
Torque Specification
9.5 ft-lbs (12 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
3 Fuel Injector Rail Bolts
M10 x 1.5
3
Fuel Injector Rail Bolts
M10 x 1.5
Torque Specification
9.5 ft-lbs (12 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
Fuel Pump and Tank System
1 Fuel Pump Mounting Bolts
M12 x 1.75
1
Fuel Pump Mounting Bolts
M12 x 1.75
Torque Specification
9.5 ft-lbs (12 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
2 Fuel Tank Strap Bolts
M14 x 2.0
2
Fuel Tank Strap Bolts
M14 x 2.0
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
3 Fuel Filler Neck Bolts
M12 x 1.75
3
Fuel Filler Neck Bolts
M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
Fuel Filter and Pressure Regulator System
1 Fuel Filter Bolt/Nut
M10 x 1.5
1
Fuel Filter Bolt/Nut
M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
2 Fuel Pressure Regulator Nut
M12 x 1.75
2
Fuel Pressure Regulator Nut
M12 x 1.75
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 25 ft-lbs (34 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
Electrical Connectors
1 Fuel Injector Electrical Connector Bolts
M6 x 1.0
1
Fuel Injector Electrical Connector Bolts
M6 x 1.0
Torque Specification
0.9 ft-lbs (1.2 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
2 Fuel Pump Electrical Connector Bolts
M6 x 1.0
2
Fuel Pump Electrical Connector Bolts
M6 x 1.0
Torque Specification
0.9 ft-lbs (1.2 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
Fuel Tank Vent Valve
1 Fuel Tank Vent Valve Mounting Bolts
M10 x 1.5
1
Fuel Tank Vent Valve Mounting Bolts
M10 x 1.5
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated bolt size. Consult manufacturer's instructions for specific torque values.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
A/C Compressor Mounting
1 A/C Compressor Mounting Bolts
M12 x 1.5
1
A/C Compressor Mounting Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
A/C Line Fittings
1 A/C Line Fittings
M10 x 1.25
1
A/C Line Fittings
M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
A/C Condenser Mounting
1 A/C Condenser Mounting Bolts
M14 x 1.5
1
A/C Condenser Mounting Bolts
M14 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on industry standards.
A/C Evaporator Mounting
1 A/C Evaporator Mounting Bolts
M10 x 1.25
1
A/C Evaporator Mounting Bolts
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on industry standards.
A/C Compressor Clutch
1 A/C Compressor Clutch Bolt
M12 x 1.5
1
A/C Compressor Clutch Bolt
M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value based on industry standards.
A/C Refrigerant Line Brackets
1 A/C Refrigerant Line Bracket Bolts
M8 x 1.25
1
A/C Refrigerant Line Bracket Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on industry standards.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Strut and Shock Absorber Mounting
1 Strut/Shock Absorber Mounting Bolts
M12 x 1.5
1
Strut/Shock Absorber Mounting Bolts
M12 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
2 Coil Spring Mounting Bolts
M10 x 1.25
2
Coil Spring Mounting Bolts
M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Control Arm and Steering Knuckle
1 Control Arm Bolts
M14 x 1.5
1
Control Arm Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
2 Steering Knuckle Bolts
M14 x 1.5
2
Steering Knuckle Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
3 Upper Control Arm Bushing Bolts
M10 x 1.25
3
Upper Control Arm Bushing Bolts
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on industry standards.
4 Lower Control Arm Bushing Bolts
M10 x 1.25
4
Lower Control Arm Bushing Bolts
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on industry standards.
Ball Joint and Tie Rod End
1 Ball Joint Nut
M12 x 1.5
1
Ball Joint Nut
M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
2 Tie Rod End Nut
M10 x 1.25
2
Tie Rod End Nut
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Sway Bar Link
1 Sway Bar Link Nut
M10 x 1.25
1
Sway Bar Link Nut
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the recommended torque specification for the lug nuts on a 2005-2011 Ram Dakota?
Q1
What IS the recommended torque specification for the lug nuts on a 2005-2011 Ram Dakota?
110 ft-lbs (150 Nm) for steel wheels and 140 ft-lbs (190 Nm) for alloy wheels
Q2 What type of torque wrench IS recommended for tightening critical bolts on the Dakota?
Q2
What type of torque wrench IS recommended for tightening critical bolts on the Dakota?
A calibrated click-type torque wrench that meets or exceeds industry standards (e.g., ANSI, ISO)
Q3 Can I use an impact wrench to tighten bolts on my Dakota?
Q3
Can I use an impact wrench to tighten bolts on my Dakota?
Impact wrenches should be avoided for critical bolts, as they can over-tighten and damage the bolt or component. Use only a calibrated torque wrench.
Q4 What IS the torque specification for the oil drain plug on a Ram Dakota?
Q4
What IS the torque specification for the oil drain plug on a Ram Dakota?
25 ft-lbs (34 Nm)
Q5 Do I need to re-torque the lug nuts after driving a certain distance?
Q5
Do I need to re-torque the lug nuts after driving a certain distance?
Yes, it IS recommended to re-torque the lug nuts after 50-100 miles (80-160 km) of driving, especially after new tires or wheels have been installed.
Q6 What are the consequences of over-tightening bolts?
Q6
What are the consequences of over-tightening bolts?
Over-tightening can strip threads, damage bolts or components, and compromise the safety and structural integrity of the vehicle.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
24 Piece Socket Set (3/8 Inch Drive)
Provides a comprehensive range of sockets for various bolt sizes encountered on the Ram Kota.
- Durable chrome vanadium steel construction
- Deep sockets for recessed bolts
- 12-point sockets for added strength
- Organized storage case for easy access
Torque Wrench Adapter (1/2 to 3/8 Inch)
Allows you to use the 3/8 inch drive torque wrench with larger bolts that require a 1/2 inch drive socket.
- Precision-machined for accurate torque readings
- Durable steel construction
- Easy to install and remove
Service Procedures
Tightening Cylinder Head Bolts
Step-by-step guide to properly tighten the cylinder head bolts to the specified torque.
- Remove the valve cover and intake and exhaust manifolds.
- Clean the bolt threads and apply engine oil.
- Tighten the bolts in the correct sequence and torque to 110 ft-lbs (150 Nm).
- Reinstall the manifolds and valve cover.
Adjusting Front Wheel Bearing Preload
Procedure for correctly adjusting the front wheel bearing preload to ensure proper hub rotation.
- Jack up the front of the vehicle and remove the wheel.
- Locate the bearing adjustment nut and loosen it.
- Tighten the nut until you feel resistance, then back it off 1/8 of a turn.
- Reinstall the wheel and torque the lug nuts to 100 ft-lbs (135 Nm).
- Check for excessive play or binding in the wheel.
Technical Service Bulletins
Intake Manifold Bolt Torque Specification Correction
2008-03-12Updates the torque specifications for the intake manifold bolts due to a previous error in the service manual.
2005-2007 Dakota with 3.7L V6 engine
Resolution: Tighten the intake manifold bolts to 18 ft-lbs (25 Nm) following the revised procedure.
Rear Axle Differential Cover Bolt Tightening Procedure
2010-08-05Provides a detailed procedure for tightening the rear axle differential cover bolts to prevent leaks.
2009-2011 Dakota with Dana 44 rear axle
Resolution: Clean the bolt threads and apply gasket sealer. Tighten the bolts to 25 ft-lbs (34 Nm) in a star pattern.
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.